How To Glue Car Window

Download Article

Download Article

Modern soft convertible car tops often have glass windows glued to the cloth, vinyl or other soft material with a melted plastic strip instead of a clear vinyl window sewn to it. If and when the glass comes unstuck -- sometimes due to the canvas shrinking from fail or otherwise -- information technology can be very hard to reattach. Double-sided foam record such equally 3M VHB record (what one writer used, others could be OK too) can reattach them, but should be applied in a specific way to avert constant strain that will break its bond.

Steps

1. i

   Reattach the soft tiptop material ("canvass") to the drinking glass when just part of the sail has discrete so that the glass does not have to be re-centered within the pigsty in the canvas. If it does have to be re-centered 1 might do that by measuring distances with the defrosting grid as a guide and, in any case, holding the drinking glass temporarily in place with gaffer's or other sticky tape.

2. two

   Open the top slightly and so that it is not taut. Prop something such every bit a small-scale empty box betwixt the front border of the top and the upper edge of the windshield frame so that the top stays open up slightly.

   Advertisement

3. 3

   Observe the seal that was attached but has become unattached, such as the lower edge of the exterior layer of canvas. ^[1] If dirt has accumulated in the pocket that has been exposed to the weather you may wish to vacuum out any large particles.

4. 4

   If only a very pocket-sized office has separated leave it alone. If a large office is generally separated yous may wish to separate information technology entirely to re-seal information technology every bit 1 continuous piece.^[two]

5. 5

   Clean the mating surfaces with rubbing alcohol.

6. 6

   Shut the roof completely to see where the canvas falls on the glass when pulled gently flat as far in on the glass as it will become, merely not pulled hard. At least in the example of cotton wool canvas, this volition probably be not as far upward onto the glass as originally (or as on a all the same-attached inside layer) because it will accept shrunk since new.

7. seven

   Re-open up the roof slightly and re-prop it.

8. eight

   Utilise a strip of double-sided cream record such as 3M VHB ("very high bail")--cream so that it volition conform to any irregularities, preferably black and then ultraviolet rays volition not promptly destroy its exposed edge--to the drinking glass with the edge coming upward to the signal you lot determined previously. ^[iii]

9. nine

   Bring the middle of the area being fastened (such every bit the middle, left-versus-right-wise of the bottom exterior canvas) up to the edge of the record. It should have just a niggling slack, since information technology needs to be pulled basically polish but not taut when the top is airtight. Just a footling slack when the top is closed is much improve than tension, which will unstick the tape.

10. 10

    Stick the canvas to the record, working outward. The reason to work outward from a fundamental point is so that any "backlog" cloth does not build up at ane side.^[4]

11. xi

    Rub down the sail over the tape firmly and employ some oestrus--non a great painfully hot amount--with a blow dryer for a thorough bond.

    • The convertible top should be fixed.

Advertisement

Add New Question

• Question

  How much will it cost to replace the top with the original window?

  

  I have a 2007 Mustang convertible. The window is separating from the material peak. I went to two convertible top/upholstery shops, and both told me the window is estrus sealed and the entire top needed to be replaced, and both gave me a price of $ane,900.

• Question

  I have in my garage a Corvette convertible with a sail elevation in groovy status. The seal around the glass rear window has popped, will this procedure work?

  

  I used 3M window weld on our 2004 Volvo C70 height and it worked great! Brand sure you get as much of the one-time adhesive off as possible. Put the 3M primer on first and let it dry for about 10 minutes. Put a dewdrop (about 3/16) of window weld on it. Clamp it in identify. I used some paint stirrer sticks & C clamps. Let information technology sit for nearly 24 hours. Exercise non do this if temperature is below forty degrees F.

• Question

  Where can I go 3M VHB foam tape?

  

  Amazon has it in a diverseness of lengths and widths.

• Question

  Can Gorilla glue be used to attach glass to a convertible canvas summit?

  

  No. I tried it and the heat from sitting in the lord's day made it scissure and come apart.

• Question

  How much will information technology cost to supercede a rear window on a convertible Sebring?

  

  The shops will tell y'all a new top is needed. Fortunately, the Sebring window lays on top of the sail flap rather than hanging from it. People swear by Rhinoceros glue for about twenty bucks. I'm planning to remove the window, clean the entire lip that the window edge contacts, put a bead of rhino on it and lay the window dorsum in. Removing it completely will let me to position it evenly in the hole since the meridian material has near likely shrunk over the years but if yours is just pulling apart in a section you can open up the top part mode and glue the lip while tension is off.

• Question

  Should I glue the inside and the outside of the window?

  

  Brett Gilbert

  Top Answerer

  Yes, if the canvas is loose on the inside office of the window, gum information technology as well.

• Question

  Where can I find instructions that are more specific to the type of auto I have?

  

  Brett Gilbert

  Top Answerer

  Yous could contact the manufacturer or a mechanic to see what they recommend. Usually, though, they will tell yous to replace the unabridged hood. The gum or tape techniques work well for just well-nigh whatever car.

Inquire a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertisement

• It may exist better to get the top stock-still in a style for whose possible failure someone else such equally a dealer volition have responsibility. Just this is a bang-up alternative to replacing the top.

Advertisement

Things You'll Need

• 3M VHB foam tape, black

About This Article

Thanks to all authors for creating a page that has been read 206,197 times.

Did this article help you?

Source: https://www.wikihow.com/Reattach-Rear-Window-Glass-to-a-Convertible-Car-Top

Posted by: mosleylerning.blogspot.com

Share this post